Urine Flow Test

January 16, 2018

A urine flow test calculates the speed of urine flow over time. It may be used to check how the bladder and sphincter are working.

The bladder is part of the urinary tract. It’s a hollow muscular organ that relaxes and expands to store urine. It then contracts and flattens to empty urine through the tube that carries urine from the bladder out of the body (urethra).

The sphincter muscle is a circular muscle. It closes tightly, like a rubber band, around the bladder opening. This helps keep urine from leaking.

For this test, you will urinate into a special funnel that is connected to a measuring instrument. The instrument calculates the amount of urine, rate of flow in seconds, and the length of time until all urine has been passed. This information helps evaluate how well the lower urinary tract is working. It also helps figure out if there is a blockage of normal urine outflow.

During normal urination, the initial urine stream starts slowly, but speeds up until the bladder is nearly empty. The urine flow then slows again until the bladder is empty. In people with a urinary tract blockage, this pattern of flow is changed, and increases and decreases more gradually. The urine flow test graphs this information, taking into account your gender and age.

A urine flow test is a quick, simple test that gives useful feedback about the health of the lower urinary tract. It is often used to see if there is blockage to normal urine outflow. Medical conditions that can change normal urine flow include:

  • Benign prostatic hypertrophy (BPH). This is enlargement of the prostate gland. It is not caused by cancer and usually happens in men over age 50. The prostate wraps around the urethra. When it is enlarged, it can narrow the urethra and interfere with normal passage of urine from the bladder. If left untreated, the enlarged prostate can block the urethra completely.
  • Cancer of the prostate or bladder
  • Urinary blockage. Blockage of the urinary tract can happen for many reasons along any part of the urinary tract–from the kidneys to the urethra. It can lead to a backup of urine causing infection, scarring, or even kidney failure if untreated.
  • Neurogenic bladder dysfunction. This is trouble with the function of the bladder due to a nervous system problem, such as a spinal cord tumor or injury.
  • Frequent urinary tract infections. These can cause scarring and damage in the urinary tract.

There may be other reasons for your healthcare provider to recommend a urine flow test.

A urine flow test is safe for most people. The test is usually done in a private bathroom or procedure area.

There may be risks depending on your specific medical condition. Be sure to discuss any concerns with your healthcare provider before the procedure.

Certain factors or conditions may interfere with the accuracy of a urine flow test. These factors include:

  • Straining with urination
  • Constipation
  • Your bladder is not full of urine
  • Body movement during urination
  • Certain medicines that affect bladder and sphincter muscle tone
  • Your healthcare provider will explain the procedure and you can ask questions.
  • Generally, no prior preparation, such as fasting (not eating or drinking) is needed.
  • You may be told to drink about 4 glasses of water several hours before the test to be sure that your bladder is full. Do not empty your bladder before arriving for the procedure.
  • If you are pregnant or think you may be, tell your healthcare provider.
  • Make sure your healthcare provider has a list of all medicines (prescription and over-the-counter), herbs, vitamins, and supplements that you are taking.

Based on your medical condition, your healthcare provider may request other specific preparation.

A urine flow test may be done on an outpatient basis or as part of your stay in the hospital. Procedures may vary depending on your condition and your healthcare provider's practices.

Generally, a urine flow test follows this process:

  1. You will be taken into the procedure area and told how to use the urine flow test device, called a flowmeter.
  2. When you are ready to urinate, you will press the flowmeter start button and count for 5 seconds before beginning urination.
  3. You will start to urinate into the funnel device that is attached to a regular toilet or portable commode. The flowmeter will record information as you are urinating.
  4. You should not push or strain as you urinate. You should stay as still as possible.
  5. When you are done urinating, you will count for 5 seconds and press the flowmeter button again.
  6. You should not put any toilet paper into the funnel device.
  7. The test will be done at this point. Depending on your condition, you may be asked to repeat the test over several days.

Generally, there is no special type of care after a urine flow test.

Your healthcare provider may give you other instructions after the procedure, depending on your situation.

Before you agree to the test or the procedure make sure you know:

  • The name of the test or procedure
  • The reason you are having the test or procedure
  • What results to expect and what they mean
  • The risks and benefits of the test or procedure
  • What the possible side effects or complications are
  • When and where you are to have the test or procedure
  • Who will do the test or procedure and what that person’s qualifications are
  • What would happen if you did not have the test or procedure
  • Any alternative tests or procedures to think about
  • When and how will you get the results
  • Who to call after the test or procedure if you have questions or problems
  • How much will you have to pay for the test or procedure


January 16, 2018


Adult Urodynamics: AUA/SUFU Guideline. American Urological Association

Reviewed By:  

Greenstein, Marc, DO,Finke, Amy, RN, BSN